Release of DinBox RTU M4: IEC 60870-5-104/Modbus device!

Release of DinBox RTU M4: IEC 60870-5-104/Modbus device!
The DinBox RTU M4 is a micro RTU with LTE Cat. 1/GPRS communication integrated for SCADA applications. The remote terminal unit maps Modbus RTU registers to IEC 60870-5-104 objects and can also perform I/O alarming or other applications. It is a cost-effective all-in solution to integrate your devices in an IEC 60870-5-104 environment. The device is equipped with TLS security.

The DinBox RTU M4 is a low-cost micro RTU with built-in wide range AC power supply. The power supply comes with a supercap back-up, in order to ensure the required energy to communicate with the SCADA system, even after a mains  power supply disconnect. Direct WAN communication is possible thanks to the built-in Sierra Wireless communication module. Everything is managed by a powerful Cortex M4 microcontroller. Finally, the RTU is built into a DIN rail mountable housing.

The DinBox RTU M4 uses IEC 60870-5-104 to communicate as a Slave with the SCADA IEC 60870-5-104 Master system. The DinBox has 8 active digital inputs, which enables monitoring events when a change has been detected. Furthermore, it has 2 digital outputs which can becontrolled via SCADA commands, and 2 analogue inputs to monitor.
Thanks to the modbus RTU-to-IEC104 mapping the DinBox RTU M4 can be used as a gateway to connect other modbus slave IEDs. Also the DinBox RTU M4 has the capacity to be connectecd by (up to) 6 Master SCADA IEC 60870-5-104.

Authentication, integrity and security are provided per application or service running on the RTU by protecting the transport layer of the protocol stack with TLS (Transport Layer Security). Integrating TLS in a non-TLS SCADA setup can be done by installing a TLS Proxy service. This service runs on the trusted network and serves as an endpoint towards the TLS RTU. Also the RTU has an ethernet port which allows LAN or WAN routing.

The DinBox RTU M4 can be remotely managed for mass firmwares (Q1 2020), remote parametrization and 'Plug & Play automatic commissioning (Q1 2020).

Specifications:

  • Communication
    Sierra Wireless CF3 HL footprint
    HL7692 – FDE band LTE Cat-1 with dual band
    GSM/GPRS/EDGE fallback
    SIM card and/or eSIM
    eUICC possibilities
    50 ohm FME antenna connector
  • Interfaces & Connectors
    RS-232 non-isolated (used for debugging)
    RS-485 / 2-wire galvanically isolated (used for
    modbus connection)
    LAN 10/100Mbit/s
    MMC/SD memory card holder
    8x DI active 24 Vdc
    2x DO optomos 'solid state', 600 Vpeak / 90 mAmax
    2x AI 0-5 Vdc, non-isolated, 12-bit single ended ADC
  • Protocols
    IEC 60870-5-104 (up to 6 Masters can connect to the RTU slave function)
    NMKD-3085 ASCII
    FTP
    Modbus RTU
    MQTT (Q2 2020)
  • Security
    Authentication and Data Encryption via TLS (Transport Layer Security)
  • Configuration
    Local via HTML GUI
    Remote via HTML GUI & Telnet commands
  • Power Supply
    85-264 AC or 9-25V DC
    Watchdog reset
    Supercap backup or NiMH rechargeable battery pack
  • Housing
    Type: Phoenix Dinrail enclosure
    Housing material: Reinforced polyamide fiber
    Housing type: DINrail housing side element, two pieces necessary to close base element, 1,5mm thick.
    DINrail snapslot for easy DINrail mounting
    Color: green
    Dimensions housing: : 172 mm x 35 mm x 135 mm
    Ambient temperature (operation) -40°C +105°C
    Inflammability class acc. to UL 94: HB
    Power dissipation at 20°C in horizontal mounting position: 8.9W 18.3W
    IP51
date_range Published on 07-01-2020 13:05
person Dominiek Truyers
visibility Views: 427
chat Comments: 0
thumb_upLikes: 0

Comments ( 0 )

There are no comments yet

Reply

Log in to reply